Biological Waste Incinerators

TECHNICAL INCINERATORS REQUIREMENTS FOR 2 health centers in Kenya

TECHNICAL INCINERATORS SPECS FOR 2 medical facilities

INTRO

• All the incinerators to be supplied and installed must meet the Government of Kenya waste Management Regulation 2006 in particular 3^rdschedule regulation (26, 47) pertaining classification, standards, criteria, and procedure for installing/operating incinerators as authored by the National Environmental Management and Coordination (waste management) regulation 2006, legal notice No. 121 of 29^th September 2006
• The capacity of the incinerator required should be to the specifications with a capacity to burn 100kgs/Hr
• The incinerator shall be run on a 3-phase power supply (mains)
• For the technical evaluation, not only the treatment plant but the entire system will be considered.  It will be the responsibility of the Bidder to supply a full system, including all eventually additionally necessary secondary systems and additional equipment.
• The system offered shall be designed to operate normally under the conditions of the purchaser’s country. The conditions include Power Supply, Climate, Temperature, Humidity, etc.
• The Bidder must provide a warranty for one year.
• All text, parameter etc. on all control operating interfaces as well as on information displays and on print-outs shall be in English language.
• The Bidder is responsible for all permits and approvals for importation. The Bidder shall provide all the necessary documentation in order to facilitate the legal requirements for the installation and putting into use of the equipment.
• Period of Execution is 90 days from contract signature for delivery to site and completion of all verification operations required for the issuance of provisional acceptance.
• Representatives of the Contracting Authority and the Beneficiary, together with the Bidder’s representative, shall carry out the controls, testing and initial approval for provisional and final acceptance as.  The provisional and final acceptance shall take place at the final destination.
• After-Sales Service: The Bidder is required to ensure that a maintenance, service and repair centre, which is authorised by the Manufacturer, and which is able to rapidly supply genuine spare parts and consumables recommended by the Manufacturer is available throughout the one year warranty period. In fulfillment of this requirement with their offer Bidders must submit a statement signed by a representative of the manufacturer:
  • Providing the name and address of its authorised maintenance, service and repair centre,
  • Confirming that this authorised maintenance, service and repair centre is able to rapidly supply genuine spare parts and the consumables recommended by the Manufacturer; and

• The Bidder will be responsible to deliver and install all to be supplied equipment at to be set up waste handling areas in the Republic of Kenya. The Bidder shall deliver a time schedule over the complete construction and assembling period. The delivery and installation time must be agreed between bidders, target Hospital and the Contracting Authority. The treatment plant must arrive pre-assembled. The Bidder shall ensure that all parts of the plant transported by sea shall not be shipped as “deck cargo”.

• It is expected that the Bidder cooperates closely with the contractor for the new waste handling building/area and will make available all needed technical information, drawing, etc. to the contractor.

• The Bidder shall supply and install the incinerator with the following attached specifications

TECHNICAL INCINERATORS SPECIFICATIONS FOR EAPHLNP
ITEM	DESCRIPTION	UNIT	QTY	RATE	KSHS.
	Incinerator
	To supply and install the following		2NO.
	Hospital Incinerators to Nema standards
	The following are the incinerator specifications :-
A	Ø      Waste type:      Mixed type 0,1,2,3 & 4 hospital/clinical bio hazard waste
	Ø      Waste density:   125 to 350Kg/M³
	Ø      Waste CV:        4000 KCAL/Kg
	Ø      Moisture content:   10-25%
	Ø      Estimated ash residue: 5-10%
	Ø      Nominal capacity:   100Kg/hour batch load
	Ø      Secondary chamber:  2 second @ 1100ºC
	Ø      Environmental:    NEMA ACT           (EMCA) 1999
	Clean Air Act 1999
	BS3316 1987
	Equipment	Set
	The Incinerator must comprise of: –
	Ø      Manual Loading door (heavy duty steel door with appropriate refractory lining)
	Ø      Horizontal solid hearth, refractory lined primary combustion chamber 800mm diameter x 2100mm long
	Ø      Full sized bulk load/ash removal door
	Ø      1 off diesel-fired ignition burner – temperature controlled
	Ø      1 off combustion air supply fan and distribution system, automatic control
	Ø      High capacity secondary combustion chamber 2 second @ 1100ºC with
	Ø      1 off diesel-fired afterburner – temperature controlled
	Ø      Control Panel – automatic operation
	Ø      Temperature indication primary and secondary chambers 0-1200ºC. Both chambers must be insulated with refractory material (super duty 100mm thick firebrick with 25mm thick calcium silicate insulation)
	Ø      Refractory lined flanged chimney to a height of 10M and it must be 3m above the height of any existing roof adjacent to the incinerator
	Carried Forward To Collection Page.
	NOTE: WE REQUIRE TWO INCINERATORS. ONE
ITEM	DESCRIPTION	UNIT	QTY	RATE	KSHS.
B	Diesel Tank:
	To provide for diesel service tank (Capacity 400 litres) including level indicator The tank requirement to be attached to the burner at a better level to make it possible for free-flow of diesel from the storage space tank to the burner.	Item	1
C	Installation & commissioning works
D	Positioning of Incinerator: – EVALUATION STANDARD	Item	1
E	Connect burners to fuel supply.	No.	2
F	Chimney Installation:
G	Composition of the chimney: – Analysis will certainly be performed in 4 phases particularly initial assessment of documents for uniformity with obligatory demands, technical assessment, website check out and additionally commercial exam. 100 Pass mark for technical analysis is 70/100 marks	Item.	1
H	Commissioning & Training:
	Testing set operating parameters, training of operators and technical staff.	Item	1
I	Commissioning Maintenance Contract
	Before the expiry of the warranty/signing off, the suppler shall provide a one-year replacement service parts (e.g. filters, air filters), the Quarterly routine maintenance price per quarter for three (3) quarters. Maintenance contract proposal).  The maintenance contract price includes labour, transport and accommodation for the attending technicians.	Item	3

Stage 3: Internet Site Browse With

The assessment committee will certainly check out the properties of the prospective purchasers who are receptive to technical evaluation stage to validate the credibility of legal documents sent out; establish the accuracy of the information offered in the tender documents, analyze firm’s capacity, area, to call a couple of.
LOCATION V– – TIMETABLE OF STANDARD

NO

NO

1

NO

1

ITEM	DESCRIPTION	UNIT	QTY	MARKS ALLOCATED	MARKS RECEIVED
	Incinerator
	To supply and install the following		2NO.
	Hospital Incinerator to Nema standards
	The following are the incinerator specifications :-
A	Ø      Waste type:      Mixed type 0,1,2,3 & 4 hospital/clinical bio hazard waste			35
	Ø      Waste density:   125 to 350Kg/M³
	Ø      Waste CV:        4000 KCAL/Kg
	Ø      Moisture content:   10-25%
	Ø      Estimated ash residue: 5-10%
	Ø      Nominal capacity:   100Kg/hour batch load
	Ø      Secondary chamber:  2 second @ 1100ºC
	Ø      Environmental:    NEMA ACT           (EMCA) 1999
	Clean Air Act 1999
	BS3316 1987
	Equipment	Set
	The Incinerator must comprise of: –
	Ø      Manual Loading door (heavy duty steel door with appropriate refractory lining)
	Ø      Horizontal solid hearth, refractory lined primary combustion chamber 800mm diameter x 2100mm long
	Ø      Full sized bulk load/ash removal door
	Ø      1 off diesel-fired ignition burner – temperature controlled
	Ø      1 off combustion air supply fan and distribution system, automatic control
	Ø      High capacity secondary combustion chamber 2 second @ 1100ºC with
	Ø      1 off diesel-fired afterburner – temperature controlled
	Ø      Control Panel – automatic operation
	Ø      Temperature indication primary and secondary chambers 0-1200ºC. Both chambers must be insulated with refractory material (super duty 100mm thick firebrick with 25mm thick calcium silicate insulation)
	Ø      Refractory lined flanged chimney to a height of 10M and it must be 3m above the height of any existing roof adjacent to the incinerator
ITEM	DESCRIPTION	UNIT	QTY	RATE	KSHS.
B	Diesel Tank:
	To provide for diesel service tank (Capacity 400 litres) including level indicator Hallmark of tenderer	Item	1	20
C	Installation & commissioning works
D	Positioning of Incinerator: – Note: In situation of variance in between system price as well as total quantity, the device price will control.	Item	1	10
E	Connect burners to fuel supply.	No.	2	5
F	Chimney Installation:
G	Composition of the chimney: – AREA VI – – – – CONVENTIONAL FORMS TECHNICAL INCINERATORS SPECS FOR 2 clinical centers INTRODUCTORY	Item.	1	10
H	Commissioning & Training:
	Testing set operating parameters, training of operators and technical staff.	Item	1	10
I	Commissioning Maintenance Contract
	Before the expiry of the warranty/signing off, the suppler shall provide a one-year replacement service parts (e.g. filters, air filters), the Quarterly routine maintenance price per quarter for three (3) quarters. Maintenance contract proposal).  The maintenance contract price includes labour, transport and accommodation for the attending technicians.	Item	3	10
	TOTAL			The container need to be affixed to the incinerator at a greater level to make it possible for free-flow of diesel from the storage tank to the burner.

EXAM CRITERIA

Analysis will be executed in 4 stages specifically preliminary examination of files for uniformity with required demands, technical assessment, site check out as well as likewise industrial exam.

100

Pass mark for technological evaluation is 70/100 marks

Phase 3: Web Site Browse Through

The assessment board will inspect out the properties of the potential buyers that are responsive to technical analysis phase to confirm the credibility of lawful data sent out; develop the accuracy of the details provided in the tender documents, analyze company’s ability, location, to call a few.

Phase 4 Company Analysis

ITEM Quotes that pass the above 3 (3) phases will be contrasted on the basis of prices/ cost approximated and the most affordable valued will definitely be taken into factor to consider the cheapest analyzed proposal as well as additionally consequently suggested for honor.	ITEM DESCRIPTION	UNIT	QTY. REQUIRED	UNIT PRICE (KHS)	REMARKS
1.	Supply, Delivery, installation and commissioning of Incinerator in	NO	1
2.	Supply, Delivery, installation and commissioning of Incinerator	NO	1

Trademark of tenderer

Note: In case of inconsistency in between system cost and total amount, the unit rate will dominate.

SECTION VI – – STANDARD FORMS

1. Form of tender
2. Contract form
3. Confidential Questionnaire form
4. Tender security form
5. Performance security form
6. Bank guarantee for advance payment
7. Declaration form