www.njctw.com
We are looking at a simple incinerator which should be fired using domestic LPG bottles. Other sources of ignition can be considered as well but we need to keep it simple. Section VI. Requirements 2-86 required for preventive maintenance for five years and where necessary include stock of recommended spare-parts for corrective maintenance. n) Training
Read More
medical waste diesel incinerator Burning Rate:47.5–50kg/hour Minimum Operating Temperature:850o C(primary combustion) Maximum Operating Temperature:1450 oC(Afterburner chamber) Secondary Burning Capacity:Compulsory Density Insulation:20mm High Refractory Casting:Minimum 65mm Heavy duty refracting lining to withstand:1500 oC Average burn out time :maximum:3 hrs Fuel type:Diesel Fuel Consumption in L/hr:7.5 to 9 Residence time in secondary chamber:2sec Residue ash post 100kg:Max 3.8kg Device for preventing infectious
Read More
l) Ease of Use and maintenance i) The unit should be simple to learn to use, operate, and maintain. ii) The unit should have abbreviated operating instructions included on or with the unit (e.g., on a laminated card attached to the unit). iii) The unit should be easy to clean, disinfect, and/or sterilize, as appropriate. iv) The unit should be
Read More
Air exhaust needs develop restrictions on the quantity of contaminants that can be launched into the ambience. Table 1. Air Emission Demands for Solid Waste Incinerators Requirements Numeric Criterion Description Dioxins and Furans 80 pg I-TEQ/cubic metre Gadget of procedure is picograms of International Toxicity Matchings per cubic metre of air Mercury 20 µg/ Rcubic metre System of treatment is
Read More
j) Controls i) The controls (i.e., switches, knobs, etc.) should be visible and clearly identified, and their functions should be self-evident. ii) Device design should prevent misinterpretation of displays and control settings. iii) Switches and controls should be protected against accidental setting changes (e.g., due to someone brushing against the panel). iv) Controls should be sealed against penetration of liquids.
Read More
HICLOVER, Nanjing Clover Medical Development Co., Ltd, supply system options for medical ecological management, animal as well as also household pet dog cremation design, various other municipal solid waste incineration job. We offer single combustion chamber, double burning chambers, 3 burning chambers as well as likewise multi-combustion chambers waste incinerators for research laboratory, center, university hospital, medical center, hygiene clinical
Read More
Functional Abilities PROCESS MINIMUM 1 TON PER DAY OPERATED WITH LIMITED TRAINING REGULAR MAINTENANCE CAN BE COMPLETED WITH LIMITED TRAINING COMPLIES WITH EURO / OR US-EPA EMISSION STANDARDS ABILITY TO BURN WASTE LUBRICANTS (POL) HANDLE ORGANIC SOLIDS (TO INCLUDE RMW) DEPLOYABLE MOBILE 24 HRS OF CONTINUOUS USE AUTOMATIC LOADING SYSTEM AUTOMATED ASH REMOVAL SYSTEM GAS SCRUBBING SYSTEM 95% REDUCTION OF
Read More
Incinerate: medical waste and general waste Capacity to burn waste: 400-500kg/hr Fuel: Diesel Fuel Consumption: 10 liters/hr maximum Incineration temperature: 950-1300 degrees centigrade Casing: thick (min 5mm) stainless steel casing and fully insulated to withstand sea humidity Voltage 220/240v or 380/415V Frequency 50Hz high-capacity, powerful, European Standard incinerator,ideal for high volume incineration,with integral after-burner for greater efficiency and emissions control.
Read More
SCHEDULE 2 TECHNICAL SPECIFICATIONS OF THE INCINERATOR General Description Previous experience in the supply, installment as well as appointing of burners Overall plant layout Feed chamber/charging Primary combustion chamber Particulate scrubbers Acid gas The stack/chimney. Minimum capacity of primary chamber = 10cubic meters Burn rate (rate of waste incineration) = 10 kg per hour Should have a full width counterbalance
Read More
Temperature: ambient temperature ranges between 21 – 450 C or more in poorly ventilated rooms. The hottest month of the year is March. Environmental temperature can be such that inferior rubber and plastic materials can easily melt or deformed. Bidders must ensure all materials will be able to withstand such temperatures 4) Humidity: humidity is usually high about 65
Read More